Telix 的使用方法重點說明:
0.請先打開 電腦 和 Modem
1.進入 Telix
C:\TELIX>telix
----------------------------------------------------------------------------
Telix Copyright (C) 1986-94 deltaComm Development, PO Box 1185, Cary, NC 27512.
Version 3.22, released 01-31-94
-- To order Telix, call 1-800-TLX-8000 --
-- For Technical Support call 1-919-460-4556 --
Press ALT-Z for help on special keys.
ATZ
OK
AT S7=45 S0=0 V1 X4
OK
Alt-Z for Help * ANSI-BBS * 38400讙81 FDX * * * * Offline
-----------------------------------------------------------------------------
以上為 TELIX 的起始畫面和起始參數,若出現 OK 字樣,表示 MODEM 起始沒問題,
若卡住了或沒出現 OK 字樣,則代表有問題,請檢查 MODEM 之接線和電源,
若仍無法啟動,請按 [ALT-X] 離開(或重新開機),將 \TELIX\TELIX.CNF 刪除,
打 TELIX 重新設定再進入.
2.按 [ALT-Z] 之求助畫面
-----------------------------------------------------------------------------
┌──────────────────────────────────────┐
│ Telix v3.22 Command Summary │
│ │
│ Main Functions Other functions │
│ │
│Dialing directory..Alt-D Queue Redial #s....Alt-Q │Run editor........Alt-A│
│Send files.........Alt-S Receive files......Alt-R │Local echo........Alt-E│
│Exit Telix.........Alt-X Run script (Go)....Alt-G │Screen Image......Alt-I│
│Comm Parameters....Alt-P cOnfigure Telix....Alt-O │DOS command.......Alt-V│
│Key defs./macros...Alt-K Terminal emulation.Alt-T │Translate Table...Alt-W│
│Capture toggle.....Alt-L Scroll Back........Alt-B │Chat Mode.........Alt-Y│
│DOS Functions......Alt-F Jump to DOS shell..Alt-J │Status Toggle.....Alt-8│
│Hang-up modem......Alt-H Clear screen.......Alt-C │DOORWAY mode......Alt-=│
│Usage Log toggle...Alt-U Misc. functions....Alt-M │Printer on/off...Ctrl-@│
│ │Send BREAK.....Ctrl-End│
│ Select function or press Enter for none. │Add LF Toggle.....S-Tab│
│ │
│Copyright (C) 1986-94 deltaComm Development, PO Box 1185, Cary, NC 27512 USA│
├──────────────────────┬───────────────┤
│ Time .. 09:07:53 Online .... No │ Capture ... Off │
│ Date .. 06-23-96 │ Printer ... Off │
│ Baud .. 38400 Terminal .. ANSI-BBS │ Script .... │
│ Comm .. N,8,1 Port ...... COM2 │ Reg. Key .. TELIX.KEY │
│ Echo .. Off Add LF .... Off │ Dial Dir .. TELIX.FON │
└──────────────────────┴───────────────┘
-----------------------------------------------------------------------------
重要按鍵說明:
Dialing directory..Alt-D (撥號電話簿)
Send files.........Alt-S (上傳檔案)
Exit Telix.........Alt-X (離開 TELIX)
Comm Parameters....Alt-P (設定通訊參數)
Key defs./macros...Alt-K (設定巨集鍵)
Capture toggle.....Alt-L (螢幕畫面抓取開關,可記錄傳輸過程)
DOS Functions......Alt-F
Hang-up modem......Alt-H (切線,結束通訊,但最好依 BBS 的指令處理)
Usage Log toggle...Alt-U (使用記錄檔開關)
Queue Redial #s....Alt-Q
Receive files......Alt-R (下傳檔案)
Run script (Go)....Alt-G (執行 腳本檔)
cOnfigure Telix....Alt-O (設定 TELIX 組態)
Terminal emulation.Alt-T (終端機模擬)
Scroll Back........Alt-B
Jump to DOS shell..Alt-J (暫時跳到 DOS)
Clear screen.......Alt-C (清除螢幕)
Misc. functions....Alt-M
Run editor.........Alt-A
Local echo.........Alt-E (本地回應)
Screen Image.......Alt-I
DOS command........Alt-V
Translate Table....Alt-W
Chat Mode..........Alt-Y (交談模式)
Status Toggle......Alt-8
DOORWAY mode.......Alt-=
Printer on/off....Ctrl-@
Send BREAK......Ctrl-End
Add LF Toggle......S-Tab
3.按 [ALT-O] 設定 TELIX 組態
┌─ Configure Telix ──────┐
│ │
│ Change which default settings? │
│ │
│ Screen and color │
│ Terminal options │
│ General options -------一定要檢查設定
│ Modem and dialing │
│ Filenames and paths -------一定要檢查設定
│ Ascii transfers │
│ Protocol options │
│ Kermit transfers │
│ Comm port setup │
│ Write setup to disk │
│ Exit │
│ │
└────────────────┘
選 General options 時
│
│A - Port COM2 Baud 38400 Parity None Data bits 8 Stop bits 1 │
│ │
│B - Emulate before translate table... Off │
│C - Default terminal type ........... ANSI-BBS ─進 BBS 站要設為如此 │
│D - Status line ..................... Bottom │
│E - Local echo ...................... Off │
│F - Add Line Feeds after CRs ........ Off │
│G - Strip high bit (incoming data) .. Off │
│H - Received Backspace destructive .. On │
│I - Backspace key sends ............. BS │
│J - XON/XOFF software flow control .. Off ┐ │
│K - CTS/RTS hardware flow control ... On ├ 高速 MODEM 要設為如此 │
│L - DSR/DTR hardware flow control ... Off ┘ │
│M - Compuserve Quick B transfers .... On │
│N - Zmodem auto-downloads ........... On │
│O - Drop CTS during disk writes...... Off │
│P - Answerback string (ENQ) ......... │
│ │
│ │
│Change which setting? (Return or Esc to exit) │
└───────────────────────────────────┘
選 Filenames and paths 時
┌─ Filenames and paths ────────────────────────┐
│ │
│ A - Download directory: │
│ c:\telix\ (這個一定要設,可不同目錄) │
│ B - Upload directory: │
│ c:\telix (這個一定要設,可不同目錄) │
│ C - Script directory: │
│ │
│ D - Default Startup Script: │
│ │
│ E - Default Capture file: │
│ TELIX.CAP │
│ F - Default Usage Log name: │
│ TELIX.USE │
│ G - Directory program: │
│ │
│ H - Screen Image file: │
│ TELIX.IMG │
│ I - Editor name: │
│
│
4.檢查以下狀態是否正確?
Alt-Z for Help * VT102 * 38400讙81 FDX * * * * Offline
^^^^^
若以上的不是 ANSI-BBS 但要進 BBS 時,請 按 [ALT-T]
┌─ Terminal emulation ─┐
│ │
│ TTY │
│ ANSI-BBS │
│ VT102 │
│ VT52 │
│ AVATAR │
│ ANSI │
│ │
└────────────┘
5.撥電話進 BBS 站
ATZ
OK
AT S7=45 S0=0 V1 X4
OK
atdt029972884 (要撥電話出去時,指令如左, atdt + 電話號碼,或按
[ALT-D] 去選)
6.BBS 的檔案上傳方法: (下傳方法較簡單,就略過了)
1.輸入 BBS 的檔案服務功能選項
2.選擇 [U] 上傳功能
3.選擇 傳輸協定 (一般為 Z-MODEM)
4.輸入上傳檔案檔名(此時不要輸入路徑)
5.輸入上傳檔案之說明(最少4個字,若為私人檔案,則在前頭加 / 符號)
6.若不再輸入其他檔案,則按 [ENTER] 離開
7.按 [S] 或 [ENTER] 開始傳輸,此時畫面會出現一串亂碼.
以上請參照各 BBS 之畫面指示
8.選擇 TELIX 的上傳檔案功能,請按 [ALT-S]
9.輸入 傳輸協定
┌────────┐
│ Which protocol?│
│ │
│ ASCII │
│ CIS Quick B │
│ Kermit │
│ Modem7 │
│ SEAlink │
│ Telink │
│ Xmodem │
│ 1k-Xmodem │
│ G-1k-Xmodem │
│ Ymodem (Batch) │
│ YmodEm-g │
│ Zmodem ------------ 一般均選 Z-MODEM (要和 BBS 上同)
│ Quit │
│ │
└────────┘
10.選擇上傳之實際檔案之路徑檔名,再按 [F10] 上傳
┌─────────────────────────────────────┐
│ │
│ ┌─ Path/Directory ─────────────────────────┐ │
│ │ C:\TELIX\ (請在此輸入要上傳檔案的路徑/目錄/檔名) │ │
│ └──────────────────────────────────┘ │
│ │
│ ┌─ Filelist ─┐ ┌─ Tagged Files ────────┐ ┌─ Drives ─┐ │
│ │ ..\ │ │TELIX.ARJ │ │ C: │ │
│ │ ANSI.KEY │ │ │ │ D: │ │
│ │ AUSSIE.REG │ │ │ │ │ │
│ │ AVATAR.KEY │ │ │ │ │ │
│ │ BRITAIN.DOC │ │(要在此有檔案時才可上傳,且檔名要│ │ │ │
│ │ BRITAIN.REG │ │和在 BBS 上輸入的檔名要一樣,選好│ │ │ │
│ │ CIS.SLT │ │後,按 F10 上傳. │ │ │ │
│ │ DEMON.CAP │ │ │ │ │ │
│ │ DEUTSCH.REG │ │ │ │ │ │
│ └───────┘ └────────────────┘ └──────┘ │
│ │
│ F3 : Tag All Space/Enter : Tag or Untag Files F10: Upload │
│ F4 : UnTag All Tab/ShiftTab : Move between views ESC: Abort │
└─────────────────────────────────────┘
11.若有出現傳輸進度畫面,則代表已在傳檔了,一般傳完之後會有傳檔成功之訊息!
可在此時觀察 MODEM 傳輸之效果!
加強說明:
1.請多注意 BBS 出現之訊息,很多問題之解答都在裡面.
如 同檔名之檔案已存在(則無法上傳)
已超過每日傳檔量或傳檔比例(則無法下傳)